add generate nlsr.conf bash script

nlsr_configs/generate-advertising.sh

@@ -0,0 +1,16 @@
+#!/bin/bash
+cat << EOF
+
+; the advertising section contains the configuration settings of the name prefixes
+; hosted by this router
+
+advertising
+{
+  ; the ndnname is used to advertised name from the router. To advertise each name prefix
+  ; configure one block of ndnname configuration command for every name prefix.
+
+  ;prefix /ndn/edu/test1           ; name in ndn URI format
+  ;prefix /ndn/edu/test2
+}
+
+EOF

nlsr_configs/generate-fib.sh

@@ -0,0 +1,22 @@
+#!/bin/bash
+cat << EOF
+
+; the fib section is used to configure fib entrys type to ndn FIB updated by NLSR
+
+fib
+{
+  ; the max-faces-per-prefix is used to limit the number of faces for each name prefixes
+  ; by NLSR in ndn FIB
+
+  max-faces-per-prefix 3   ; default value 0. Valid value 0-60. By default (value 0) NLSR adds
+                           ; all available faces for each reachable name prefixes in NDN FIB
+
+  ; routing-calc-interval is the time to wait in seconds after a routing table calculation is
+  ; scheduled before actually performing the routing table calculation
+
+  routing-calc-interval 15   ; default value 15. Valid values 0-15. It is recommended that
+                             ; routing-calc-interval have a higher value than adj-lsa-build-interval
+}
+
+
+EOF

nlsr_configs/generate-hyperbolic.sh

@@ -0,0 +1,20 @@
+#!/bin/bash
+cat << EOF
+
+; the hyperbolic section contains the configuration settings of enabling a router to calculate
+; routing table using [hyperbolic routing table calculation](http://arxiv.org/abs/0805.1266) method
+
+hyperbolic
+{
+  ; commands in this section follows a strict order
+  ; the switch is used to set hyperbolic routing calculation in NLSR
+
+  state off             ; default value 'off', set value 'on' to enable hyperbolic routing table
+                        ; calculation which turns link state routing 'off'. set value to 'dry-run'
+                        ; to test hyperbolic routing and compare with link state routing.
+
+
+  radius   123.456      ; radius of the router in hyperbolic coordinate system
+  angle    1.45,2.36    ; angle of the router in hyperbolic coordinate system
+}
+EOF

nlsr_configs/generate-neighbour.sh

@@ -1,7 +1,8 @@
 #!/bin/bash
-TEMP_DIR=../temp
 name=$1
-transName=$(echo ${routerName//\//.})
+
+TEMP_DIR=../temp
+transName=$(echo ${name//\//.})
 transName=$(echo ${transName#.})
 nbs=$(cat $TEMP_DIR/$transName.nbs)
 cat << EOF
@@ -49,24 +50,18 @@ let 'length = length - 1'
 for index in `seq 0 $length`
 do
     neighbourName=$(echo $nbs | jq -r ".[$index].name")
+    faceUri=ether://[$(echo $nbs | jq -r ".[$index].targetMac")]
+    linkCost=25
+    cat << EOF
+    neighbor 
+    {
+        name $neighbourName ; name prefix of the neighbor router consists
+                            ; of network, site-name and router-name
+        face-uri $faceUri   ; face uri of the face connected to the neighbor
+        link-cosr $linkCost ; cost of the connecting link to neighbor
+
+    }
+EOF
 done
 
-  needighbor
-  {
-    name /ndn/edu/%C1.Router/pkun2  ; name prefix of the neighbor router consists
-                                                ; of network, site-name and router-name
-
-    face-uri  ether://[a0:36:9f:85:c4:9f]       ; face uri of the face connected to the neighbor
-    link-cost 25                                ; cost of the connecting link to neighbor
-  }
-  
-  neighbor
-  {
-    name /ndn/edu/%C1.Router/pkun3  ; name prefix of the neighbor router consists
-                                                ; of network, site-name and router-name
-
-    face-uri  ether://[a0:36:9f:85:c9:de]       ; face uri of the face connected to the neighbor
-    link-cost 25                                ; cost of the connecting link to neighbor
-  }
-
-}
+echo }

nlsr_configs/generate-security.sh

@@ -0,0 +1,21 @@
+#!/bin/bash
+cat << EOF
+
+security
+{
+  validator
+  {
+    trust-anchor
+    {
+      type any
+    }
+  }
+  prefix-update-validator
+  {
+    trust-anchor
+    {
+      type any
+    }
+  }
+}
+EOF

nlsr_configs/generate.sh

@@ -0,0 +1,12 @@
+#!/bin/bash
+name=$1
+network=$2
+site=$3
+router=$4
+
+cat /dev/null > nlsr.conf
+./generate-general.sh $network $site $router >> nlsr.conf
+./generate-neighbour.sh $name >> nlsr.conf
+./generate-hyperbolic.sh >> nlsr.conf
+./generate-fib.sh >> nlsr.conf
+./generate-security.sh >> nlsr.conf

nlsr_configs/nlsr.conf

@@ -0,0 +1,140 @@
+; the general section contains all the general settings for router
+general
+{
+  ; mandatory configuration command section network, site and router
+
+  network /ndn         ; name of the network the router belongs to in ndn URI format
+  site /edu/pkusz    ; name of the site the router belongs to in ndn URI format
+  router /pkun1    ; name of the router in ndn URI format
+
+  ; lsa-refresh-time is the time in seconds, after which router will refresh its LSAs
+  lsa-refresh-time 1800      ; default value 1800. Valid values 240-7200
+
+  ; router-dead-interval is the time in seconds after which an inactive routers
+  ; LSAs are removed
+  ;router-dead-interval 3600 ; default value: 2*lsa-refresh-time. Value must be larger
+                             ; than lsa-refresh-time
+
+  ; InterestLifetime (in seconds) for LSA fetching
+  lsa-interest-lifetime 4    ; default value 4. Valid values 1-60
+
+  ; sync interest lifetime of ChronoSync in milliseconds
+  sync-interest-lifetime 60000  ; default value 60000. Valid values 1000-120,000
+
+  seq-dir       /var/lib/nlsr        ; path for sequence directory (Absolute path)
+}
+neighbors
+{
+  ; in case hello interest timed out, router will try 'hello-retries' times at 'hello-timeout'
+  ; seconds interval before giving up for any neighbors (deciding link is down)
+
+   hello-retries 3                     ; interest retries number in integer. Default value 3
+                                       ; valid values 1-10
+
+   hello-timeout 1                    ; interest time out value in integer. Default value 1
+                                       ; Valid values 1-15
+
+   hello-interval  60                  ; interest sending interval in seconds. Default value 60
+                                       ; valid values 30-90
+
+  ; adj-lsa-build-interval is the time to wait in seconds after an Adjacency LSA build is scheduled
+  ; before actually building the Adjacency LSA
+
+  adj-lsa-build-interval 5   ; default value 5. Valid values 0-5. It is recommended that
+                             ; adj-lsa-build-interval have a lower value than routing-calc-interval
+
+  ; first-hello-interval is the time to wait in seconds before sending the first Hello Interest
+
+  first-hello-interval  10   ; Default value 10. Valid values 0-10
+
+  face-dataset-fetch-tries 3 ; default is 3. Valid values 1-10. The FaceDataset is
+                             ; gotten from NFD, and is needed to configure NLSR
+                             ; correctly. It is recommended not to set this
+                             ; variable too high, because it could cause
+                             ; congestion for NFD.
+
+  face-dataset-fetch-interval 3600 ; default is 3600. Valid values 1800-5400.
+                                   ; This controls how often (in seconds) NLSR will attempt to
+                                   ; fetch a FaceStatus dataset from NFD.
+
+  ; neighbor command is used to configure router's neighbor. Each neighbor will need
+  ; one block of neighbor command
+    neighbor 
+    {
+        name /ndn/edu/pkusz/pkun3 ; name prefix of the neighbor router consists
+                            ; of network, site-name and router-name
+        face-uri ether://[a0:36:9f:85:c9:dc]   ; face uri of the face connected to the neighbor
+        link-cosr 25 ; cost of the connecting link to neighbor
+
+    }
+    neighbor 
+    {
+        name /ndn/edu/pkusz/pkun2 ; name prefix of the neighbor router consists
+                            ; of network, site-name and router-name
+        face-uri ether://[a0:36:9f:85:c4:9f]   ; face uri of the face connected to the neighbor
+        link-cosr 25 ; cost of the connecting link to neighbor
+
+    }
+    neighbor 
+    {
+        name /ndn/edu/pkusz/main2 ; name prefix of the neighbor router consists
+                            ; of network, site-name and router-name
+        face-uri ether://[00:1b:21:09:09:10]   ; face uri of the face connected to the neighbor
+        link-cosr 25 ; cost of the connecting link to neighbor
+
+    }
+}
+
+; the hyperbolic section contains the configuration settings of enabling a router to calculate
+; routing table using [hyperbolic routing table calculation](http://arxiv.org/abs/0805.1266) method
+
+hyperbolic
+{
+  ; commands in this section follows a strict order
+  ; the switch is used to set hyperbolic routing calculation in NLSR
+
+  state off             ; default value 'off', set value 'on' to enable hyperbolic routing table
+                        ; calculation which turns link state routing 'off'. set value to 'dry-run'
+                        ; to test hyperbolic routing and compare with link state routing.
+
+
+  radius   123.456      ; radius of the router in hyperbolic coordinate system
+  angle    1.45,2.36    ; angle of the router in hyperbolic coordinate system
+}
+
+; the fib section is used to configure fib entrys type to ndn FIB updated by NLSR
+
+fib
+{
+  ; the max-faces-per-prefix is used to limit the number of faces for each name prefixes
+  ; by NLSR in ndn FIB
+
+  max-faces-per-prefix 3   ; default value 0. Valid value 0-60. By default (value 0) NLSR adds
+                           ; all available faces for each reachable name prefixes in NDN FIB
+
+  ; routing-calc-interval is the time to wait in seconds after a routing table calculation is
+  ; scheduled before actually performing the routing table calculation
+
+  routing-calc-interval 15   ; default value 15. Valid values 0-15. It is recommended that
+                             ; routing-calc-interval have a higher value than adj-lsa-build-interval
+}
+
+
+
+security
+{
+  validator
+  {
+    trust-anchor
+    {
+      type any
+    }
+  }
+  prefix-update-validator
+  {
+    trust-anchor
+    {
+      type any
+    }
+  }
+}